資料介紹
The MAX6652 system supervisor monitors multiple power-supply voltages, including its own, and also features an on-board temperature sensor. Voltages and temperature are converted to an 8-bit code using an analog-to-digital converter (ADC). A multiplexer automatically sequences through the voltage and temperature measurements. The digitized signals are then stored in registers and compared to the over/under threshold limits programmed over the 2-wire serial interface.
When a temperature measurement exceeds the programmed threshold, or when an input voltage falls outside the programmed voltage limits, the MAX6652 generates a latched interrupt output active-low ALERT. Three interrupt modes are available for temperature excursions: default mode, one-time interrupt mode, and comparator mode. The active-low ALERT output is cleared, except for temperature interrupts generated in comparator mode, by reading the interrupt status register (Table 5). The active-low ALERT output can also be masked by writing to the appropriate bits in the interrupt mask register (Table 6) or by setting bit 1 of the configuration register (Table 4) to 0. The MAX6652 I2C*-compatible/SMBus? interface also responds to the SMB alert response address.
The 2-wire serial interface accepts both I2C and standard system management bus (SMBus) write byte, read byte, send byte, and receive byte commands to program the alarm thresholds and to read voltage and temperature data. Voltage data is scaled so that when the nominal voltage is present at a pin (e.g., 3.3V for the 3.3VIN pin), the conversion result is equal to 3/4 of the ADC full-scale range or a decimal count of 192 (Table 3). The temperature data format is 7 bits plus sign, with each data bit representing 1°C, in two's complement format (Table 2).
The MAX6652 has only one address pin, ADD. One of four different address codes can be selected by connecting the ADD pin to GND, VCC, SDA, or SCL. Whenever an I2C-compatible/SMBus transaction is initiated, the two LSBs of the slave address register are determined by connection, setting the chip address to one of four possible values. In addition, an address code can also be directly written to the serial address register. This code will overwrite the code set by connection of the ADD pin, until the MAX6652 is taken through a power-on reset cycle.
The MAX6652 features 60Hz or 50Hz line-frequency rejection for optimal performance. The device operates from +2.7V to +5.5V and is specified for operation from -40°C to +125°C. It is available in a tiny 10-pin μMAX? package.
When a temperature measurement exceeds the programmed threshold, or when an input voltage falls outside the programmed voltage limits, the MAX6652 generates a latched interrupt output active-low ALERT. Three interrupt modes are available for temperature excursions: default mode, one-time interrupt mode, and comparator mode. The active-low ALERT output is cleared, except for temperature interrupts generated in comparator mode, by reading the interrupt status register (Table 5). The active-low ALERT output can also be masked by writing to the appropriate bits in the interrupt mask register (Table 6) or by setting bit 1 of the configuration register (Table 4) to 0. The MAX6652 I2C*-compatible/SMBus? interface also responds to the SMB alert response address.
The 2-wire serial interface accepts both I2C and standard system management bus (SMBus) write byte, read byte, send byte, and receive byte commands to program the alarm thresholds and to read voltage and temperature data. Voltage data is scaled so that when the nominal voltage is present at a pin (e.g., 3.3V for the 3.3VIN pin), the conversion result is equal to 3/4 of the ADC full-scale range or a decimal count of 192 (Table 3). The temperature data format is 7 bits plus sign, with each data bit representing 1°C, in two's complement format (Table 2).
The MAX6652 has only one address pin, ADD. One of four different address codes can be selected by connecting the ADD pin to GND, VCC, SDA, or SCL. Whenever an I2C-compatible/SMBus transaction is initiated, the two LSBs of the slave address register are determined by connection, setting the chip address to one of four possible values. In addition, an address code can also be directly written to the serial address register. This code will overwrite the code set by connection of the ADD pin, until the MAX6652 is taken through a power-on reset cycle.
The MAX6652 features 60Hz or 50Hz line-frequency rejection for optimal performance. The device operates from +2.7V to +5.5V and is specified for operation from -40°C to +125°C. It is available in a tiny 10-pin μMAX? package.
下載該資料的人也在下載
下載該資料的人還在閱讀
更多 >
- max3232技術資料下載datasheet 46次下載
- MAX6369–MAX6374 datasheet pdf
- MAX6033 datasheet pdf
- MAX1647,MAX1648 datasheet pdf
- MAX1645,MAX1645A datasheet pdf
- MAX700,MAX701,MAX702 datasheet
- MAX6679 datasheet pdf
- MAX603,MAX604 datasheet pdf
- AD6652,pdf datasheet (12-Bit,
- MAX6143,pdf datasheet (Tempera
- MAX130, MAX131 pdf datasheet (
- MAX121 pdf datasheet (308ksps
- MAX3244 pdf datasheet (RS-232
- MAX516 pdf datasheet
- MAX514 pdf datasheet
- max30100和max30102的區別 4404次閱讀
- 配合MAX9217/MAX9218/MAX9247/MAX9248/MAX9250評估板工作 2109次閱讀
- MAX6652系統監測器將電壓監測與溫度檢測相結合 715次閱讀
- 分享一個快速閱讀datasheet的方法 2311次閱讀
- 如何閱讀Datasheet,是作為電子工程師的必備技能! 7837次閱讀
- AD9如何簡單快速的制作出原理圖符號 7441次閱讀
- 使用pdf解析可以用來讀取PDF文件中字符串文本,圖片數據 1.3w次閱讀
- max3485與max485區別詳解(解析為什么max3485不能代替max485) 10w次閱讀
- MAX232引腳圖功能應用電路 MAX232中文資料PDF數據手冊下載 1.4w次閱讀
- MAX706s_MAX706SESA_MAX706TESA_MAX706PA中文資料PDF英文Datasheet數據手冊 5133次閱讀
- MAX14576,MAX14636,MAX14637 USB充電器檢測器 1755次閱讀
- MAX9039–MAX9043,MAX9050–MAX9053低功耗比較器與精密電壓基準源 1782次閱讀
- MAX5134-MAX5137內最小的16位DAC 1724次閱讀
- 如何優化MAX16974-MAX16976的電路布局 2036次閱讀
- MAX5970應用電路 2656次閱讀
下載排行
本周
- 1TC358743XBG評估板參考手冊
- 1.36 MB | 330次下載 | 免費
- 2開關電源基礎知識
- 5.73 MB | 11次下載 | 免費
- 3嵌入式linux-聊天程序設計
- 0.60 MB | 3次下載 | 免費
- 4DIY動手組裝LED電子顯示屏
- 0.98 MB | 3次下載 | 免費
- 5基于FPGA的C8051F單片機開發板設計
- 0.70 MB | 2次下載 | 免費
- 651單片機窗簾控制器仿真程序
- 1.93 MB | 2次下載 | 免費
- 751單片機PM2.5檢測系統程序
- 0.83 MB | 2次下載 | 免費
- 8基于51單片機的RGB調色燈程序仿真
- 0.86 MB | 2次下載 | 免費
本月
- 1OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234315次下載 | 免費
- 2555集成電路應用800例(新編版)
- 0.00 MB | 33566次下載 | 免費
- 3接口電路圖大全
- 未知 | 30323次下載 | 免費
- 4開關電源設計實例指南
- 未知 | 21549次下載 | 免費
- 5電氣工程師手冊免費下載(新編第二版pdf電子書)
- 0.00 MB | 15349次下載 | 免費
- 6數字電路基礎pdf(下載)
- 未知 | 13750次下載 | 免費
- 7電子制作實例集錦 下載
- 未知 | 8113次下載 | 免費
- 8《LED驅動電路設計》 溫德爾著
- 0.00 MB | 6656次下載 | 免費
總榜
- 1matlab軟件下載入口
- 未知 | 935054次下載 | 免費
- 2protel99se軟件下載(可英文版轉中文版)
- 78.1 MB | 537798次下載 | 免費
- 3MATLAB 7.1 下載 (含軟件介紹)
- 未知 | 420027次下載 | 免費
- 4OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234315次下載 | 免費
- 5Altium DXP2002下載入口
- 未知 | 233046次下載 | 免費
- 6電路仿真軟件multisim 10.0免費下載
- 340992 | 191186次下載 | 免費
- 7十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183279次下載 | 免費
- 8proe5.0野火版下載(中文版免費下載)
- 未知 | 138040次下載 | 免費
評論
查看更多