企業號介紹

全部
  • 全部
  • 產品
  • 方案
  • 文章
  • 資料
  • 企業

華秋商城

元器件現貨采購/代購/選型一站式BOM配單

1.8w 內容數 99w+ 瀏覽量 187 粉絲

TI微控制器 (MCU)TMS570LS1224

--- 產品詳情 ---

16/32 位 RISC 閃存 MCU,Cortex R4F,通過 Q100 車規認證
CPU Arm Cortex-R4F
Frequency (MHz) 160, 180
ADC 2 x 12-Bit (24ch)
GPIO 64, 101
UART 2
Number of I2Cs 1
Features Hercules high-performance microcontroller
TI functional safety category Functional Safety-Compliant
Operating temperature range (C) -40 to 125
Power supply solution TPS65381A-Q1
  • High-Performance Automotive-Grade Microcontroller for Safety-Critical Applications
    • Dual CPUs Running in Lockstep
    • ECC on Flash and RAM Interfaces
    • Built-In Self-Test (BIST) for CPU and On-chip RAMs
    • Error Signaling Module With Error Pin
    • Voltage and Clock Monitoring
  • ARM Cortex-R4F 32-Bit RISC CPU
    • 1.66 DMIPS/MHz With 8-Stage Pipeline
    • FPU With Single- and Double-Precision
    • 12-Region Memory Protection Unit (MPU)
    • Open Architecture With Third-Party Support
  • Operating Conditions
    • Up to 180-MHz System Clock
    • Core Supply Voltage (VCC): 1.14 to 1.32 V
    • I/O Supply Voltage (VCCIO): 3.0 to 3.6 V
  • Integrated Memory
    • 1.25MB of Program Flash With ECC
    • 192KB of RAM With ECC
    • 64KB of Flash for Emulated EEPROM With ECC
  • 16-Bit External Memory Interface (EMIF)
  • Common Platform Architecture
    • Consistent Memory Map Across Family
    • Real-Time Interrupt (RTI) Timer (OS Timer)
    • 128-Channel Vectored Interrupt Module (VIM)
    • 2-Channel Cyclic Redundancy Checker (CRC)
  • Direct Memory Access (DMA) Controller
    • 16 Channels and 32 Control Packets
    • Parity Protection for Control Packet RAM
    • DMA Accesses Protected by Dedicated MPU
  • Frequency-Modulated Phase-Locked Loop (FMPLL) With Built-In Slip Detector
  • Separate Nonmodulating PLL
  • IEEE 1149.1 JTAG, Boundary Scan and ARM CoreSight Components

  • Advanced JTAG Security Module (AJSM)
  • Calibration Capabilities
    • Parameter Overlay Module (POM)
  • 16 General-Purpose Input/Output (GPIO) Pins Capable of Generating Interrupts
  • Enhanced Timing Peripherals for Motor Control
    • 7 Enhanced Pulse Width Modulator (ePWM) Modules
    • 6 Enhanced Capture (eCAP) Modules
    • 2 Enhanced Quadrature Encoder Pulse (eQEP) Modules
  • Two Next Generation High-End Timer (N2HET) Modules
    • N2HET1: 32 Programmable Channels
    • N2HET2: 18 Programmable Channels
    • 160-Word Instruction RAM Each With Parity Protection
    • Each N2HET Includes Hardware Angle Generator
    • Dedicated High-End Timer Transfer Unit (HTU) for Each N2HET
  • Two 12-Bit Multibuffered Analog-to-Digital Converter (MibADC) Modules
    • ADC1: 24 Channels
    • ADC2: 16 Channels Shared With ADC1
    • 64 Result Buffers Each With Parity Protection
  • Multiple Communication Interfaces
    • Three CAN Controllers (DCANs)
      • 64 Mailboxes Each With Parity Protection
      • Compliant to CAN Protocol Version 2.0A and 2.0B
    • Inter-Integrated Circuit (I2C)
    • Three Multibuffered Serial Peripheral Interface (MibSPI) Modules
      • 128 Words Each With Parity Protection
      • 8 Transfer Groups
    • Up to Two Standard Serial Peripheral Interface (SPI) Modules
    • Two UART (SCI) Interfaces, One With Local Interconnect Network (LIN 2.1) Interface Support
  • Packages
    • 144-Pin Quad Flatpack (PGE) [Green]
    • 337-Ball Grid Array (ZWT) [Green]

The TMS570LS1224 device is a high-performance automotive-grade microcontroller family for safety systems. The safety architecture includes dual CPUs in lockstep, CPU and memory BIST logic, ECC on both the flash and the data SRAM, parity on peripheral memories, and loopback capability on peripheral I/Os.

The TMS570LS1224 device integrates the ARM Cortex-R4F floating-point CPU which offers an efficient 1.66DMIPS/MHz, and has configurations which can run up to 180 MHz providing up to 298 DMIPS. The device supports the word-invariant big-endian [BE32] format.

The TMS570LS1224 device has 1.25MB of integrated flash and 192KB of data RAM with single-bit error correction and double-bit error detection. The flash memory on this device is a nonvolatile, electrically erasable and programmable memory, implemented with a 64-bit-wide data bus interface. The flash operates on a 3.3-V supply input (same level as I/O supply) for all read, program, and erase operations. When in pipeline mode, the flash operates with a system clock frequency of up to 180 MHz. The SRAM supports single-cycle read and write accesses in byte, halfword, word, and double-word modes throughout the supported frequency range.

The TMS570LS1224 device features peripherals for real-time control-based applications, including two Next Generation High-End Timer (N2HET) timing coprocessors with up to 44 I/O terminals, seven Enhanced Pulse Width Modulator (ePWM) modules with up to 14 outputs, six Enhanced Capture (eCAP) modules, two Enhanced Quadrature Encoder Pulse (eQEP) modules, and two 12-bit Analog-to-Digital Converters (ADCs) supporting up to 24 inputs.

The N2HET is an advanced intelligent timer that provides sophisticated timing functions for real-time applications. The timer is software-controlled, using a reduced instruction set, with a specialized timer micromachine and an attached I/O port. The N2HET can be used for pulse-width-modulated outputs, capture or compare inputs, or general-purpose I/O (GIO). The N2HET is especially well suited for applications requiring multiple sensor information and drive actuators with complex and accurate time pulses. A High-End Timer Transfer Unit (HTU) can perform DMA-type transactions to transfer N2HET data to or from main memory. A Memory Protection Unit (MPU) is built into the HTU.

The ePWM module can generate complex pulse width waveforms with minimal CPU overhead or intervention. The ePWM is easy to use and it supports both high-side and low-side PWM and deadband generation. With integrated trip zone protection and synchronization with the on-chip MibADC, the ePWM module is ideal for digital motor control applications.

The eCAP module is essential in systems where the accurately timed capture of external events is important. The eCAP can also be used to monitor the ePWM outputs or for simple PWM generation when the eCAP is not needed for capture applications.

The eQEP module is used for direct interface with a linear or rotary incremental encoder to get position, direction, and speed information from a rotating machine as used in high-performance motion and position-control systems.

The device has two 12-bit-resolution MibADCs with 24 total inputs and 64 words of parity-protected buffer RAM each. The MibADC channels can be converted individually or can be grouped by software for sequential conversion sequences. Sixteen inputs are shared between the two MibADCs. Each MibADC supports three separate groupings of channels. Each group can be converted once when triggered or configured for continuous conversion mode. The MibADC has a 10-bit mode for use when compatibility with older devices or faster conversion time is desired. MibADC1 also supports the use of external analog multiplexers.

The device has multiple communication interfaces: three MibSPIs, two SPIs, one LIN, one SCI, three DCANs, and one I2C. The SPI provides a convenient method of serial high-speed communications between similar shift-register type devices. The LIN supports the Local Interconnect standard 2.0 and can be used as a UART in full-duplex mode using the standard Non-Return-to-Zero (NRZ) format. The DCAN supports the CAN 2.0 (A and B) protocol standard and uses a serial, multimaster communication protocol that efficiently supports distributed real-time control with robust communication rates of up to 1 Mbps. The DCAN is ideal for systems operating in noisy and harsh environments (for example, automotive and industrial fields) that require reliable serial communication or multiplexed wiring.

The I2C module is a multimaster communication module providing an interface between the microcontroller and an I2C-compatible device through the I2C serial bus. The I2C supports speeds of 100 and 400 Kbps.

A Frequency-Modulated Phase-Locked Loop (FMPLL) clock module is used to multiply the external frequency reference to a higher frequency for internal use. The Global Clock Module (GCM) manages the mapping between the available clock sources and the device clock domains.

The device also has an External Clock Prescaler (ECP) module that when enabled, outputs a continuous external clock on the ECLK terminal. The ECLK frequency is a user-programmable ratio of the peripheral interface clock (VCLK) frequency. This low-frequency output can be monitored externally as an indicator of the device operating frequency.

The Direct Memory Access (DMA) controller has 16 channels, 32 control packets, and parity protection on its memory. An MPU is built into the DMA to protect memory against erroneous transfers.

The Error Signaling Module (ESM) monitors all device errors and determines whether an interrupt or external error pin (ball) is triggered when a fault is detected. The nERROR terminal can be monitored externally as an indicator of a fault condition in the microcontroller.

The External Memory Interface (EMIF) provides a memory extension to asynchronous and synchronous memories or other slave devices.

A Parameter Overlay Module (POM) enhances the calibration capabilities of application code. The POM can reroute flash accesses to internal memory or to the EMIF, thus avoiding the reprogramming steps necessary for parameter updates in flash.

With integrated safety features and a wide choice of communication and control peripherals, the TMS570LS1224 device is an ideal solution for high-performance real-time control applications with safety-critical requirements.

為你推薦

  • 如何利用運算放大器設計振蕩電路?2023-08-09 08:08

    使用運算放大器設計振蕩電路運算放大器的工作原理發明運算放大器的人絕對是天才。中間兩端接上電源,當同相輸入大于反相輸入,右側就會輸出(接近)電源電壓(Vcc),如果反過來小于同相輸入,則輸出0V(負電源)電壓。在輸出端接上燈泡,假設我想控制燈泡循環亮滅,那就需要一會輸出高電平點亮,一會輸出低電平熄滅。也就是我需要讓左邊能自動變化大小,就能實現控制燈泡。如何讓電
  • 【PCB設計必備】31條布線技巧2023-08-03 08:09

    相信大家在做PCB設計時,都會發現布線這個環節必不可少,而且布線的合理性,也決定了PCB的美觀度和其生產成本的高低,同時還能體現出電路性能和散熱性能的好壞,以及是否可以讓器件的性能達到最優等。在上篇內容中,小編主要分享了PCB線寬線距的一些設計規則,那么本篇內容,將針對PCB的布線方式,做個全面的總結給到大家,希望能夠對養成良好的設計習慣有所幫助。1走線長度
  • 電動汽車直流快充方案設計【含參考設計】2023-08-03 08:08

    大功率直流充電系統架構大功率直流充電設計標準國家大功率充電標準“Chaoji”技術標準設計目標是未來可實現電動汽車充電5分鐘行駛400公里。“Chaoji”技術標準主要設計參數如下:最大電壓:目前1000V(可擴展到1500V);最大電流:帶冷卻系統500A(可擴展到600A);不帶冷卻系統150-200A;最大功率:900KW。大功率直流充電系統架構大功率
  • Buck電路的原理及器件選型指南2023-07-31 22:28

    Buck電路工作原理電源閉合時電壓會快速增加,當斷開時電壓會快速減小,如果開關速度足夠快的話,是不是就能把負載,控制在想要的電壓值以內呢?假設12V降壓到5V,也就意味著,MOS管開關需要42%時間導通,58%時間斷開。當42%時間MOS管導通時,電感被充磁儲能,同時對電容進行充電,給負載提供電量。當58%時間MOS管斷開時,由于電感上的電流不能突變,電路通
    1825瀏覽量
  • 100W USB PD 3.0電源2023-07-31 22:27

    什么是PD3.0快充?PD快充協議全稱“USBPowerDelivery”功率傳輸協議,簡稱為“PD協議”。2015年11月,USBPD快充迎來了大版本更新,進入到了USBPD3.0快充時代。USBPD3.0相對于USBPD2.0的變化主要有三方面:增加了對設備內置電池特性更為詳細的描述;增加了通過PD通信進行設備軟硬件版本識別和軟件更新的功能,以及增加了數
    1354瀏覽量
  • 千萬不要忽略PCB設計中線寬線距的重要性2023-07-31 22:27

    想要做好PCB設計,除了整體的布線布局外,線寬線距的規則也非常重要,因為線寬線距決定著電路板的性能和穩定性。所以本篇以RK3588為例,詳細為大家介紹一下PCB線寬線距的通用設計規則。要注意的是,布線之前須把軟件默認設置選項設置好,并打開DRC檢測開關。布線建議打開5mil格點,等長時可根據情況設置1mil格點。PCB布線線寬01布線首先應滿足工廠加工能力,
  • 基于STM32的300W無刷直流電機驅動方案2023-07-06 10:02

    如何驅動無刷電機?近些年,由于無刷直流電機大規模的研發和技術的逐漸成熟,已逐步成為工業用電機的發展主流。圍繞降低生產成本和提高運行效率,各大廠商也提供不同型號的電機以滿足不同驅動系統的需求。現階段已經在紡織、冶金、印刷、自動化生產流水線、數控機床等工業生產方面應用。無刷直流電機的優點與局限性優點:高輸出功率、小尺寸和重量、散熱性好、效率高、運行速度范圍寬、低
  • 上新啦!開發板僅需9.9元!2023-06-21 17:43

    上新啦!開發板僅需9.9元!
  • 參考設計 | 2KW AC/DC數字電源方案2023-06-21 17:43

    什么是數字電源?數字電源,以數字信號處理器(DSP)或微控制器(MCU)為核心,將數字電源驅動器、PWM控制器等作為控制對象,能實現控制、管理和監測功能的電源產品。它是通過設定開關電源的內部參數來改變其外特性,并在“電源控制”的基礎上增加了“電源管理”。所謂電源管理是指將電源有效地分配給系統的不同組件,最大限度地降低損耗。數字電源的管理(如電源排序)必須全部
  • 千萬不能小瞧的PCB半孔板2023-06-21 17:34

    PCB半孔是沿著PCB邊界鉆出的成排的孔,當孔被鍍銅時,邊緣被修剪掉,使沿邊界的孔減半,讓PCB的邊緣看起來像電鍍表面孔內有銅。模塊類PCB基本上都設計有半孔,主要是方便焊接,因為模塊面積小,功能需求多,所以通常半孔設計在PCB單只最邊沿,在鑼外形時鑼去一半,只留下半邊孔在PCB上。半孔板的可制造性設計最小半孔最小半孔的工藝制成能力是0.5mm,前提是孔必須
    2731瀏覽量