--- 產品詳情 ---
Audio input type | Analog Input |
Architecture | Class-D |
Speaker channels (Max) | Mono |
Power stage supply (Max) (V) | 5.5 |
Power stage supply (Min) (V) | 4.5 |
Load (Min) (ohms) | 4 |
Output power (W) | 2 |
SNR (dB) | 95 |
THD + N @ 1 kHz (%) | 0.2 |
Iq (Typ) (mA) | 4 |
Control interface | GPIO |
Closed/open loop | Closed |
Analog supply (Min) (V) | 4.5 |
Analog supply (Max) (V) | 5.5 |
PSRR (dB) | 77 |
Operating temperature range (C) | -40 to 85 |
- Modulation Scheme Optimized to Operate Without a Filter
- 4 mm × 4 mm MicroStar Junior BGA and TSSOP Package Options
- 2 W Into a 4- Speaker (THD+N<1%)
- <0.2% THD+N at 1.5 W, 1 kHz, Into a 4- Load
- Extremely Efficient Third Generation 5-V Class-D Technology:
- Low-Supply Current (No Filter) ...4 mA
- Low-Supply Current (Filter) . . . 7.5 mA
- Low-Shutdown Current . . . 0.05 μA
- Low-Noise Floor ...40 μVRMS(No-Weighting Filter)
- Maximum Efficiency Into 8 , 75 – 85 %
- 4 Internal Gain Settings ...6 – 23.5 dB
- PSSR . . . –77 dB
- Integrated Depop Circuitry
- Short-Circuit Protection (Short to Battery, Ground, and Load)
- APPLICATIONS
- High-Efficiency For Extended Battery Run Time
MicroStar Junior is a trademark of Texas Instruments.
The TPA2000D1 is a 2-W mono bridge-tied-load (BTL) class-D amplifier designed to drive a speaker with at least 4- impedance. The amplifier uses TI?s third generation modulation technique, which results in improved efficiency and SNR. It also allows the device to be connected directly to the speaker without the use of the LC output filter commonly associated with class-D amplifiers (this results in EMI which must be shielded at the system level). These features make the device ideal for use in devices where high-efficiency is needed to extend battery run time.
The gain of the amplifier is controlled by two input terminals, GAIN1, and GAIN0. This allows the amplifier to be configured for a gain of 6, 12, 18, and 23.5 dB. The differential input terminals are high-impedance CMOS inputs, and can be used as summing nodes.
The class-D BTL amplifier includes depop circuitry to reduce the amount of turnon pop at power up, and when cycling SHUTDOWN\.
The TPA2000D1 is available in the 16-pin TSSOP and MicroStar Junior? BGA packages that drive 2 W of continuous output power into a 4- load. TPA2000D1 operates over an ambient temperature range of ?40°C to 85°C.
為你推薦
-
TI數字多路復用器和編碼器SN54HC1512022-12-23 15:12
-
TI數字多路復用器和編碼器SN54LS1532022-12-23 15:12
-
TI數字多路復用器和編碼器CD54HC1472022-12-23 15:12
-
TI數字多路復用器和編碼器CY74FCT2257T2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74LVC257A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74LVC157A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74ALS258A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74ALS257A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74ALS157A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74AHCT1582022-12-23 15:12
-
【PCB設計必備】31條布線技巧2023-08-03 08:09
相信大家在做PCB設計時,都會發現布線這個環節必不可少,而且布線的合理性,也決定了PCB的美觀度和其生產成本的高低,同時還能體現出電路性能和散熱性能的好壞,以及是否可以讓器件的性能達到最優等。在上篇內容中,小編主要分享了PCB線寬線距的一些設計規則,那么本篇內容,將針對PCB的布線方式,做個全面的總結給到大家,希望能夠?qū)︷B(yǎng)成良好的設計習慣有所幫助。1走線長度1388瀏覽量 -
電動汽車直流快充方案設計【含參考設計】2023-08-03 08:08
大功率直流充電系統架構大功率直流充電設計標準國家大功率充電標準“Chaoji”技術標準設計目標是未來可實現電動汽車充電5分鐘行駛400公里。“Chaoji”技術標準主要設計參數如下:最大電壓:目前1000V(可擴展到1500V);最大電流:帶冷卻系統500A(可擴展到600A);不帶冷卻系統150-200A;最大功率:900KW。大功率直流充電系統架構大功率 -
Buck電路的原理及器件選型指南2023-07-31 22:28
-
100W USB PD 3.0電源2023-07-31 22:27
-
千萬不要忽略PCB設計中線寬線距的重要性2023-07-31 22:27
想要做好PCB設計,除了整體的布線布局外,線寬線距的規則也非常重要,因為線寬線距決定著電路板的性能和穩定性。所以本篇以RK3588為例,詳細為大家介紹一下PCB線寬線距的通用設計規則。要注意的是,布線之前須把軟件默認設置選項設置好,并打開DRC檢測開關。布線建議打開5mil格點,等長時可根據情況設置1mil格點。PCB布線線寬01布線首先應滿足工廠加工能力,1464瀏覽量 -
基于STM32的300W無刷直流電機驅動方案2023-07-06 10:02
-
上新啦!開發板僅需9.9元!2023-06-21 17:43
-
參考設計 | 2KW AC/DC數字電源方案2023-06-21 17:43
-
千萬不能小瞧的PCB半孔板2023-06-21 17:34