記錄Red Lite Env項目的基礎搭建過程及碰到的問題

Linux 下如何使用對 GD32F310G START 進行在線調試以及程序下載

需要使用的關鍵工具是，開源的調試器 openocd, 涉及到有兩個配置文件，分別是 target 的配置文件 gd32f3x.cfg:

# script for stm32f3x family

#
# stm32 devices support both JTAG and SWD transports.
#
source [find target/swj-dp.tcl]
source [find mem_helper.tcl]

if { [info exists CHIPNAME] } {
   set _CHIPNAME $CHIPNAME
} else {
   set _CHIPNAME stm32f3x
}

set _ENDIAN little

# Work-area is a space in RAM used for flash programming
# By default use 16kB
if { [info exists WORKAREASIZE] } {
   set _WORKAREASIZE $WORKAREASIZE
} else {
   set _WORKAREASIZE 0x4000
}

# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
#
# Since we may be running of an RC oscilator, we crank down the speed a
# bit more to be on the safe side. Perhaps superstition, but if are
# running off a crystal, we can run closer to the limit. Note
# that there can be a pretty wide band where things are more or less stable.
adapter speed 1000

adapter srst delay 100
if {[using_jtag]} {
 jtag_ntrst_delay 100
}

#jtag scan chain
if { [info exists CPUTAPID] } {
   set _CPUTAPID $CPUTAPID
} else {
   if { [using_jtag] } {
      # See STM Document RM0316
      # Section 29.6.3 - corresponds to Cortex-M4 r0p1
      set _CPUTAPID 0x4ba00477
   } {
      set _CPUTAPID 0x2ba01477
   }
}

swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu

if {[using_jtag]} {
   jtag newtap $_CHIPNAME bs -irlen 5
}

set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap

$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0

set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME stm32f1x 0 0 0 0 $_TARGETNAME

reset_config srst_nogate

if {![using_hla]} {
   # if srst is not fitted use SYSRESETREQ to
   # perform a soft reset
   cortex_m reset_config sysresetreq
}

proc stm32f3x_default_reset_start {} {
    # Reset clock is HSI (8 MHz)
    adapter speed 1000
}

proc stm32f3x_default_examine_end {} {
    # Enable debug during low power modes (uses more power)
    mmw 0xe0042004 0x00000007 0 ;# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP

    # Stop watchdog counters during halt
    mmw 0xe0042008 0x00001800 0 ;# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
}

proc stm32f3x_default_reset_init {} {
    # Configure PLL to boost clock to HSI x 8 (64 MHz)
    mww 0x40021004 0x00380400   ;# RCC_CFGR = PLLMUL[3:1] | PPRE1[2]
    mmw 0x40021000 0x01000000 0 ;# RCC_CR |= PLLON
    mww 0x40022000 0x00000012   ;# FLASH_ACR = PRFTBE | LATENCY[1]
    sleep 10                    ;# Wait for PLL to lock
    mmw 0x40021004 0x00000002 0 ;# RCC_CFGR |= SW[1]

    # Boost JTAG frequency
    adapter speed 8000
}

# Default hooks
$_TARGETNAME configure -event examine-end { stm32f3x_default_examine_end }
$_TARGETNAME configure -event reset-start { stm32f3x_default_reset_start }
$_TARGETNAME configure -event reset-init { stm32f3x_default_reset_init }

$_TARGETNAME configure -event trace-config {
    # Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
    # change this value accordingly to configure trace pins
    # assignment
    mmw 0xe0042004 0x00000020 0
}

board 的配置文件 gd32f3start.cfg

# sudo openocd -f interface/cmsis-dap.cfg -c "transport select swd" -c "set CPUTAPID 0" -f target/gd32f3x.cfg
#
source [find interface/cmsis-dap.cfg]
transport select swd

set CPUTAPID 0
set WORKAREASIZE 0x2000
source [find target/gd32f3x.cfg]

proc gdd { pos } {
    if { $pos == 0 } {
        reset;
        halt;
        flash write_image erase TencentOS_tiny.bin 0x8000000;
        reset;
        echo "stm down firm 2 internal flash success"
    } else {
        echo "invalid gdd down to others"
    }
}

分別將上述配置文件放到 openocd 的安裝目錄，大概是這樣的：

? tree -L  1 /usr/share/openocd/scripts/
/usr/share/openocd/scripts/
├── bitsbytes.tcl
├── board  ==> 放 gd32f3start.cfg 配置文件
├── chip
├── cpld
├── cpu
├── fpga
├── interface
├── mem_helper.tcl
├── memory.tcl
├── mmr_helpers.tcl
├── target  ==> 放 gd32f3x.cfg 配置文件
├── test
└── tools

9 directories, 4 files

連接開發板的命令是 openocd -f board/gd32f3start.cfg， 如果一切順利你會看到這樣的信息：

接下去可以：

使用 arm-none-eabi-gdb 連接本機的 3333 端口遠程調試開發板

使用 telnet 鏈接本機的 4444 端口進行程序下載調試

效果大概是這樣的：

環境搭建好了之后，就可以開發愉快的開發了。

移植 Tencent OS 到 GD32F310G START

移植系統比較快的方法是：

參考一個架構類似的處理器的工程，然后復制修改替換，保證編譯通過

閱讀整個系統的代碼走向，點燈調試

逐步優化代碼，最后可以提交 療 到上游

此處具體的移植步驟我就不詳細記錄了，因為網上有豐富的系統移植的教程，都是大同小異的。我在此僅僅展示下我移植過程中的一些提交記錄：

特別地，我將 TencentOS Tiny 的 shell 組件添加進來了，所以效果是這樣的：

審核編輯：劉清